Kyocera FS-1200 printer
http://usa.kyoceramita.com/...S1200ENUM.PDF
Table of contents
View All 
• FCC statement »
• Interface connectors »
• Safety information »
• Ozone concentration »
• IMPORTANT SAFEGUARDS »
• Declaration of Conformity (U »
• CE Marking Directive »
• Declaration of Conformity (Australia) »
• Canadian Department of Communications compliance statement »
• Disclaimer »
• Prolonged Non-Use and Moving the Printer »
• ENERGY STAR® »
• The action program Energy 2000 »
• Kyocera ECO-PRODUCT »
• Introduction »
• Maintenance Features »
• Print Engine Features »
• Software Features »
• Options »
• Positioning the Printer »
• Clearance »
• Places to Avoid »
• Basic requirements »
• Power Supply »
• Unpacking and Inspection »
• List of Shipped Components »
• Names of Parts »
• Front View »
• Interior View »
• Rear View »
• Setting Up and Interfacing »
• Open the top cover »
• Install the toner container »
• Close the top cover »
• Install the waste toner bottle »
• Adjust the paper guides in the cassette and add paper »
• Open the paper stopper on the face-down output tray »
• Install the face-up output tray »
• Connect the printer to the computer »
• Attach the power cord »
• Print a status page »
• Test the interface with the computer »
• Set the emulation mode »
• Install the printer driver »
• MP (Multi-Purpose) Tray Feeding »
• First Mode (Automatic Manual Feeding) »
• Cassette Mode »
• Duplex Printing from the MP tray »
• Selecting the MP Tray »
• Memory Card »
• Handling a Memory Card »
• Memory Expansion Installation »
• Removing the Main Circuit Board »
• DIMM to be used »
• Installing and Removing The DIMM »
• Testing the Expansion Memory »
• Chapter 2 Operating the Laser Printer »
• Control Panel »
• Message Display »
• Interface Indicator »
• Resolution Indicator »
• Paper Size Indicator »
• Copy Indicator »
• Symbolic Indicators »
• Control Keys »
• Operating Procedures »
• Switching Power On »
• Stack Selection »
• Feed Selection »
• On-line/Off-line Setting »
• Canceling Printing »
• Status Printout »
• Form Feed »
• Using the Mode Select Menu »
• Mode Select Menu »
• Configuring Interfaces »
• Parallel Interface »
• RAM DISK »
• Setting the RAM DISK Size »
• RAM DISK Operations »
• Operating a Memory Card »
• Hints on Writing Fonts to the Memory Card »
• Reading Fonts/Data from a Memory Card »
• Writing Data to a Memory Card »
• Deleting Data from a Memory Card »
• Formatting a Memory Card »
• Printing a list of data names »
• Setting Custom Sizes »
• Setting the Paper Type »
• Making Settings »
• Paper Type User Setting »
• Sleep (Ecopower) Mode »
• Dumping Received Data »
• KIR 2 Level »
• Ecoprint Mode »
• Resource Protection »
• Adjusting the Print Density »
• Setting the Audio Warning (Buzzer) »
• Chapter 3 Fonts »
• Internal Fonts »
• List of Fonts »
• Chapter 4 Maintenance »
• Toner Kit Replacement »
• Toner Kit to be Used »
• Supplying Toner »
• Replace the Waste Toner Bottle »
• Cleaning »
• Main Charger Unit »
• Paper Feed Unit »
• Chapter 5 Troubleshooting »
• General Guide »
• Power Problems »
• Interface Problems »
• Print Quality Problems »
• Completely blank printout »
• All-black printout »
• Dropouts, horizontal streaks, stray dots »
• Black or white vertical streaks »
• Faint or blurred printing »
• Grey background »
• Dirt on the top edge or back of the paper »
• Characters out of position »
• Indicators and Messages »
• Indicators »
• Maintenance Messages »
• Error Messages »
• Correcting a Paper Jam »
• Printer Specifications »
• Appendix B Paper Selection »
• General Guidelines »
• Paper Availability »
• Paper Specifications »
• Selecting the Right Paper »
• Special Paper »
• Transparency »
• Adhesive-Backed Labels »
• Appendix C Host Computer Interface »
• Parallel interface communication modes »
• Interface Signals »
• Serial (RS-232C/RS-422A) Interface (Option) »
• RS-232C interface »
• RS-422A interface »
• RS-232C/RS-422A Protocol »
• PRESCRIBE FRPO D0 command »
• RS-232C Cable Connection »
• Preparing an RS-232C Cable »
• Connecting the Printer to the Computer »
View All